How to Install an Air Compressor in Your Garage

How to Install an Air CompressorAir compressors are a necessity for individuals who perform operations that require various power tools. They take away the strain and sweat that characterizes hammers, saws and wrenches. It is widely being utilized in manufacturing plants and factories. However, independent craftsmen are also adopting its use in their homes.
The popularity of the air compressor is closely linked to its application to most power tools. The installation of these devices in residential garages is relatively easy but most people have no clue of how to go about it.

Selection the type an air compressor

Before an air compressor can be installed in a garage, it is important to first select the right type.

The 5 important specifications of these devices are:

  • Cubic feet per minute (cfm) – This is what determines the quantity of air that the compressor releases. The tools that will use the device are what determine the required cfm.
  • Pounds per square inch (psi) – This refers to the pressure at which a compressor delivers air. In order for a compressor to fully cater for the user’s working needs, it must be above the optimum rating for the given set of tools. The average value is 90 psi. Psi rating must be read in conjunction with the cfm ratings.
  • Horsepower – This is the motor output of the device, it is an indication of the overall power. Horsepower of an air compressor is directly proportional to the psi rating and the cfm rating. So, if a compressor has satisfactory cfm and psi ratings then its horsepower should be okay.
  • Duty cycle – This refers to the length of time that the device runs prior to shutting down for cooling purposes.
  • Tank volume – It is the quantity of compressed air that specific models of air compressors can hold. A big holding capacity translates to an easier time for the motor in usage cycles. It also helps significantly for those projects that frequently alternate between idle mode and active mode.

Installation an air compressor in your garage

After selecting a suitable air compressor and purchasing it, you can now install it in your garage.
The following are the compressive steps on how to achieve this:

  • Choose a good area whereby the compressor can stand properly.
  • Establish the quantity of room required for tool and work applications.
  • Choose the fittings and hose lengths that are sufficient for the available attachments.
  • Carefully put the compressor on top of isolator pads. This functions to lower noise vibrations and most importantly, to stabilize the machine. You should read the owner’s manual provided at time of purchase so as to acquaint yourself with the proper start-up procedure as well as the commission procedure.
  • The device can now be powered up from a close outlet.
  • Activate your pneumatic tools and start working.

Selection of a proper hose

Selection of a hose is critical to the operation of these compressors in your garage. Avoid linking compact and small air compressors with hoses of industrial length.

If a hose is too long for the kind of work space in a garage, then air loss will be experienced between the tool tip and the compressor. A hose that is 50ft. long is usually ideal for most residential garages. This provides adequate length for the setup of any system, which might extend from your garage space to the backyard, living area or the driveway.

Filter

FilterIt is advisable to attach a filter between the tank, pistons and inlet valve. This helps in preventing moisture from accessing the compressed air. Lubricants and moisture can be problematic especially for blowing, painting and sanding applications. Put a filtration device at the device’s outlet. It helps in preventing condensation from damaging pneumatic applications by diluting them.

Dryer

The setup of these devices should be linked to an oil/water separator and air dryer. A short airline can be used to link the 2 devices.

The above insightful information should help you to successfully install it in your garage.

Conclusion

Installation of an air compressor is a useful undertaking particularly for avid craftsmen. Individuals who utilize an array of manual tools for metal and wood projects are better placed with pneumatic arsenal. Compressed air systems expedite very many tasks even for those who perform all sorts of auto work in their garages.

Leave a Reply

Your email address will not be published. Required fields are marked *